| QS074 |
You have not specified a unit of measure |
| QS075 |
Characteristic is used in at least one certificate profile |
| QS076 |
Enter a unit of measurement |
| QS077 |
Master inspection characteristic is already linked to class char. &1 |
| QS078 |
The most up-to-date version is being processed |
| QS079 |
Reference to the class characteristic will not be copied |
| QS080 |
Data is preassigned in the master inspection characteristic |
| QS081 |
The class char. and the master inspection char. are not compatible |
| QS082 |
You cannot use master inspection char. as "incomplete copy model" |
| QS083 |
Enter the tolerance key |
| QS084 |
You can only change certain control indicators |
| QS086 |
Class characteristic has more than one interval |
| QS087 |
No selected set is assigned to the class characteristic |
| QS088 |
Values and control indicators are reset according to the class char. |
| QS090 |
Specification limit for the class char. differs from interval limit |
| QS091 |
Class characteristic is not released for use |
| QS093 |
Use a suitable tolerance key |
| QS094 |
Class charac. is already linked with master insp. charac. &2 in plant &1 |
| QS095 |
Class characteristic & does not exist |
| QS096 |
You cannot link class characteristic & to the master insp. characteristic |
| QS098 |
You cannot set "Data record is archived" manually |
| QS099 |
Characteristic has been archived and cannot therefore be processed |
| QS100 |
C H A R A C T E R I S T I C M E S S A G E I D s |
| QS101 |
Characteristic was not deleted |
| QS102 |
No physical-sample drawing text was entered in language & |
| QS103 |
Complete all the entries |
| QS104 |
Enter either a key date or a change number |
| QS105 |
Key date will be overwritten by the key date of the change number |
| QS106 |
Selected method version is not released |
| QS107 |
No long text exists |
| QS108 |
Select a maximum of & for the number of decimal places |
| QS109 |
You cannot maintain a tolerance key for a qualitative characteristic |
| QS110 |
No quantitative data available |
| QS111 |
You cannot enter an "*" |
| QS112 |
Status change not allowed here |
| QS113 |
For method &1 (plant &2), there is no released version for key date &3 |
| QS114 |
Specify a language |
| QS115 |
Enter the target value |
| QS116 |
Increase the class width |
| QS117 |
Target value does not lie within the tolerance change |
| QS118 |
Tolerance change results in an incorrect tolerance range |
| QS119 |
Tolerance change falls below the lower plausibility limit |
| QS120 |
Tolerance change exceeds the upper plausibility limit |
| QS121 |
Enter a validity time period for the tolerance change |
| QS122 |
Enter a number of classes |
| QS123 |
Lower specification limit is not on class limit |
| QS124 |
Both specification limits are necessary for the calculation |
| QS125 |
A class width not equal to 0 must be given for the calculation |
| QS126 |
Select a smaller class width |
| QS127 |
Select the number of classes greater than & |
| QS128 |
Target value is smaller than a lower limit |
| QS129 |
Class range exceeds the tolerance range |
| QS130 |
Class width cannot be determined because no tolerance range was specified |
| QS131 |
Target value is greater than an upper limit |
| QS132 |
Unit & is not defined |
| QS133 |
Select a class width that is smaller than the tolerance range |
| QS134 |
Class range does not overlap with the tolerance range |
| QS135 |
Class range exceeds the plausibility range |
| QS136 |
Select a class midpoint that is smaller than the upper spec. limit |
| QS137 |
Select a class midpoint that is greater than the lower spec. limit |
| QS138 |
Select a class midpoint that is smaller than the upper plausibility limit |
| QS139 |
Select a class midpoint that is greater than the lower plausibility limit |
| QS140 |
Select an upper spec. limit that is greater than the lower spec. limit |
| QS141 |
Select an upper plausibility limit that is greater than all upper limits |
| QS142 |
Select a lower plausibility limit that is smaller than all lower limits |
| QS143 |
Select a tolerance change-to that is greater than tolerance change-from |
| QS144 |
Select a time period for the change that is within the validity range |
| QS145 |
Master inspection characteristic & & & has not been created |
| QS146 |
Select a valid position |
| QS147 |
No catalog entry could be selected |
| QS148 |
Create code & or release the code group |
| QS149 |
Characteristic & & has already been created |
| QS150 |
No validity period was selected for master inspection charac. &1 &2 &3 |
| QS151 |
No characteristic was selected |
| QS152 |
No catalog entry was selected |
| QS153 |
You have not assigned a defect code |
| QS154 |
Upper specification limit is not on class limit |
| QS155 |
Method & (plant &) does not exist |
| QS156 |
When you select ENTER, the method assignment & will be deleted |
| QS157 |
Characteristic & & & has already been created |
| QS158 |
Characteristic was not changed |
| QS159 |
First make an entry in TQ01 for & |
| QS160 |
Enter a characteristic type |
| QS161 |
No time axis is available for this master inspection characteristic |
| QS162 |
Enter a catalog type and a code group/selected set |
| QS163 |
Select an upper plausiblity limit that is greater than the lower limit |
| QS164 |
Create or release code group & in catalog & |
| QS165 |
No history is available for this field |
| QS166 |
First create or release selected set & in catalog & |
| QS167 |
Select an upper specification limit that is greater than the lower limit |
| QS168 |
Select a tolerance key that corresponds to the type of characteristic |
| QS169 |
The same language code cannot be entered more than once |
| QS170 |
Valid-from date is in the past |
| QS171 |
Inspector qualification & is not defined |
| QS172 |
Check the target value. Tolerance key is used |
| QS173 |
Weighting factor is not defined |
| QS174 |
The inspection method was already assigned to this characteristic |
| QS175 |
Inspection method & & & cannot be deleted |
| QS176 |
No characteristic could be selected |
| QS177 |
No codes are assigned to code group or selected set |