| QP218 |
Reference to char. & not valid because of dyn. modif. |
| QP219 |
Sampling procedure does not fit dyn. mod. rule in char. & |
| QP220 |
No suitable characteristic found |
| QP221 |
Char. &: Physical-sample drawing text cannot be printed |
| QP222 |
Charac. & : Different smaple unit of measure for same partial sample |
| QP223 |
Charac. & : Cross-operation partial samples are not supported |
| QP224 |
Results Rec. by Insp. Unit: No Char. Without Indep. Multiple Samples (&) |
| QP225 |
Op. &1 Results Rec. by Insp. Unit: No Charac. with Single Value Recording |
| QP249 |
Dynamic modification criteria are proposed according to task list usage & |
| QP250 |
Dynamic modification rule & cannot be used |
| QP251 |
Insertion increment must be smaller than the increment itself |
| QP252 |
Dynamic modification rule is reset due to the dynamic modification level |
| QP253 |
Define dynamic modification rule & |
| QP254 |
Dynamic modification rule & is not compatible with sampling procedure |
| QP255 |
Sampling proc. & is not compatible with dynamic modification rule & |
| QP256 |
QM data: Maintain inspection point reference |
| QP257 |
QM data: maintain quantity-related data |
| QP258 |
QM data: maintain time-related data |
| QP259 |
This inspection point completion is not possible for task list type &2 |
| QP260 |
Dynamic modification criteria &1 are inconsistent |
| QP280 |
Record an insp. point of type "Freely-defined" or "Phys. sample" |
| QP281 |
Create an inspection point of the type "Physical sample" |
| QP286 |
Sample-drawing procedure only allowed for insp. point type "phys. sample" |
| QP288 |
You cannot define characteristics for standard tasks |
| QP289 |
Inspection point &1 (type &2) is not allowed for this task list type (&3) |
| QP290 |
Inconsistency in plan usage &: dyn. sampling criterion & not available |
| QP291 |
Dynamic modification rule &1 is only possible for optional characs |
| QP293 |
No dynamic modification level can be defined for usage & |
| QP294 |
Dynamic modification level & already used; & not allowed |
| QP295 |
Use & with dynamic modification criterion & already defined in plan |
| QP296 |
First delete dynamic modification data for this plan |
| QP297 |
No dynamic modification data can be defined for this task list type & |
| QP298 |
Possible dynamic modification levels: initial or 1 (lot level) |
| QP299 |
No characteristics can be defined for this plan type |
| QP300 |
No dynamic modification rule was selected |
| QP301 |
No characteristics available for operation & |
| QP302 |
CUA status (Table TC01) is not maintained |
| QP303 |
There are no dependent char. specs available for insp. char. & |
| QP304 |
Assignment already available (compare with entry &) |
| QP305 |
Enter a validity time period for the tolerance change |
| QP306 |
Assignment of material & is not available |
| QP307 |
There are no assignments |
| QP308 |
Plant & is not available |
| QP309 |
Screen & is not defined in TQ21 |
| QP310 |
The characteristic number must be between & and & |
| QP311 |
The characteristic number is too large |
| QP312 |
The allocation number is too large |
| QP313 |
Dependent characteristic specs not possible for task list type & |
| QP314 |
Characteristic & has no reference |
| QP315 |
Characteristic &1: Reference to master inspection char. &2 was cancelled |
| QP316 |
First selected characteristic reached |
| QP317 |
Last selected characteristic reached |
| QP318 |
Enter a number of classes |
| QP319 |
Enter a target value |
| QP320 |
Enter both tolerance limits |
| QP321 |
Enter a class width greater than 0 |
| QP322 |
Characteristic & is not quantitative |
| QP323 |
Select a smaller class width |
| QP324 |
First select characteristics (from the list screen) |
| QP325 |
The number of classes is greater than &. Reduce the number |
| QP326 |
The target value is smaller than the lower tolerance |
| QP327 |
The class range exceeds the tolerance range |
| QP328 |
The class width cannot be determined. Reduce the class number. |
| QP329 |
The target value is greater than the upper tolerance |
| QP330 |
Enter the characteristic category or specify a control key profile |
| QP331 |
No characteristic available |
| QP332 |
Dyn. modification level changed: Check dyn. mod. rule for insp. chars |
| QP333 |
Do not select a number of decimal places greater than & |
| QP334 |
The unit & is not defined (T006) |
| QP335 |
Check the sample unit of measure (Proposal: Operation unit of measure) |
| QP336 |
Set the unit tables for unit & |
| QP337 |
Enter a unit |
| QP338 |
Conversion factors automatically calculated |
| QP339 |
Short text line must be maintained again |
| QP340 |
Define sampling procedure & |
| QP341 |
Authorization is not allowed |
| QP342 |
Maintain inspector qualification & |
| QP343 |
Sampling procedure & cannot be used |
| QP344 |
The tolerance range is smaller than the class width entered |
| QP345 |
Enter a dynamic modification rule |
| QP346 |
Class range does not correspond to the tolerance range |
| QP347 |
Correct the dyn. modification level (only 0, 1, 3 or init. value allowed) |
| QP348 |
Class range exceeds plausibility range |
| QP349 |
There is no characteristic data on the selected screen |
| QP350 |
No master inspection characteristics are defined |
| QP351 |
Master inspection characteristic &, plant & is not available |
| QP352 |
No valid version found for master inspection characteristic & |
| QP353 |
System error during locking |
| QP354 |
Master inspection characteristic &, version & is being processed by &3 |
| QP355 |
Master inspection characteristic &1 in version &2 is not released |
| QP356 |
Insp. characteristic & is overwritten by master insp. characteristic |
| QP357 |
Check your selections |
| QP358 |
Characteristic &, version & is not available in plant & |
| QP359 |
Dependent characteristic specs for referenced insp. char. not allowed |
| QP360 |
Tolerance range cannot be calculated |
| QP361 |
Insert interval must be smaller than & |
| QP362 |
Choose a class midpoint that is smaller than the upper tolerance |
| QP363 |
Select a new insert position |
| QP364 |
Entry & is positioned (internal) |
| QP365 |
Data will be reset |