| QP366 |
Choose a class midpoint greater than the lower tolerance |
| QP367 |
Version & is the current valid version |
| QP368 |
Define characteristic weighting & |
| QP369 |
Confirm the sample unit of measure & |
| QP370 |
Set only one indicator for characteristic &: quantitative or qualitative |
| QP371 |
Lower tolerance limit is not on class limit |
| QP372 |
Upper tolerance limit is not within class limit |
| QP373 |
Choose a class midpoint that is smaller than the upper plausibility limit |
| QP374 |
Choose a class midpoint that is greater than the lower plausibility limit |
| QP375 |
Only the first selected characteristic is unlocked |
| QP376 |
Define share estimate procedure & |
| QP377 |
No share estimation procedure was selected |
| QP378 |
Share estimation procedure & and control indicator are not compatible |
| QP379 |
Select an upper tolerance that is greater than the lower tolerance |
| QP380 |
No methods defined |
| QP381 |
Method &, version &, plant & is not available |
| QP382 |
No valid version found for method &, plant & |
| QP383 |
Inspection characteristic & is linked to a class characteristic |
| QP384 |
Method &, version &, plant & is being processed by &4 |
| QP385 |
Method &, version &, plant & cannot be used |
| QP386 |
Method &, version &, plant & is not assigned to the characteristic |
| QP387 |
You cannot assign the method; a reference to the characteristic exists |
| QP388 |
Enter a method that is assigned to the master inspection characteristic |
| QP389 |
Method &, version &, plant & is not released |
| QP390 |
You cannot insert a characteristic after the last characteristic |
| QP391 |
Dependent characteristic specifications will be deleted |
| QP392 |
Dependent characteristic specifications will be checked |
| QP393 |
You have reached the first selected dependent characteristic specs |
| QP394 |
You have reached the last selected dependent characteristic specs |
| QP395 |
No value is available |
| QP396 |
Complete the data entry |
| QP397 |
Tolerances are reset |
| QP398 |
Only relative tolerances can be defined as depending on a target value |
| QP399 |
No measured values are recorded for characteristic & |
| QP400 |
Selected set & in plant & for catalog & is not available |
| QP401 |
Code group &1 does not exist in catalog &2 |
| QP402 |
No valid version for selected set & is available |
| QP403 |
No valid version for code group & is available |
| QP404 |
Selected set & in plant & cannot be used |
| QP405 |
Code group & cannot be used |
| QP406 |
Select catalog type (entry &) |
| QP407 |
Code group &2 is currently being processed by &1 |
| QP408 |
Selected set &2 in plant &3 is currently being processed by &1 |
| QP409 |
Code & in code group & is not maintained |
| QP410 |
A valid version for code & & is not available |
| QP411 |
Enter a selected set |
| QP412 |
No catalog entry & is assigned |
| QP413 |
No master inspection characteristic is assigned |
| QP414 |
No inspection method is assigned |
| QP415 |
No upper defect code is assigned |
| QP416 |
No lower defect code is assigned |
| QP417 |
Define catalog type & |
| QP418 |
No selected sets are allowed in catalog type & |
| QP419 |
Select another catalog type |
| QP420 |
Enter a selected set or code group |
| QP421 |
You do not have to enter a plant for a code group. Plant will be ignored. |
| QP422 |
You did not enter a plant. The plant will be copied from the header |
| QP423 |
Check your data |
| QP424 |
No dependent characteristic specifications are available |
| QP425 |
Catalog type & cannot be used in the characteristic |
| QP426 |
No sampling procedure assigned |
| QP427 |
No dynamic modification rule assigned |
| QP428 |
Sequences are not available in plan category & |
| QP429 |
Position operation & |
| QP430 |
Data will be copied after the cursor position (characteristic &) |
| QP431 |
Select an existing characteristic |
| QP432 |
Characteristic & refers to itself (recursion) |
| QP433 |
You cannot copy data to characteristic & |
| QP434 |
Characteristic & also contains a formula |
| QP435 |
A formula must not refer to a subsequent characteristic & |
| QP436 |
For a calculated characteristic values cannot be recorded in classes |
| QP437 |
& & |
| QP438 |
Characteristic & is not a calculated characteristic |
| QP439 |
SPC criterion & is not defined |
| QP440 |
No SPC criterion selected |
| QP441 |
SPC criterion & is reset |
| QP442 |
SPC criterion can be entered |
| QP443 |
No defect code for qualitative rejection assigned |
| QP444 |
Cursor is positioned on incorrect line |
| QP445 |
Material plan has not yet been assigned |
| QP446 |
Charac. & is not used in a material specification for plan materials |
| QP447 |
Maintain procedure for share calculation |
| QP448 |
You must know the characteristic version in order to choose a method |
| QP449 |
There is no long-term characteristic used in the formula |
| QP450 |
When you select ENTER, position only exisiting characteristics |
| QP451 |
Only position existing dependent characteristic specifications |
| QP452 |
Inspection characteristic &1 already exists |
| QP453 |
Assignment number &1 already exists |
| QP454 |
Conditional characteristic must also be a long-term characteristic |
| QP455 |
No dyn. modif. rule is assigned to specified characteristic & |
| QP456 |
Only enter a procedure for the dynamic modification rule |
| QP457 |
Test equipment & is not defined for operation |
| QP458 |
Characteristic & will not be changed |
| QP459 |
Inspection characteristic has no link to a class characteristic |
| QP460 |
Upper plausibility limit is less than the upper specification limit |
| QP461 |
Upper plausibility limit is less than upper specification limit 1 |
| QP462 |
Upper plausibility limit is less than the upper specification limit 2 |
| QP463 |
Lower plausibility limit is greater than the lower specification limit |
| QP464 |
Lower plausibility limit is greater than the lower specification limit 1 |
| QP465 |
Lower plausibility limit is greater than the lower specification limit 2 |