| QETB007 |
Data was copied to the toolbox without an operation number |
| QETB008 |
No control chart is run for this characteristic |
| QETB009 |
No log is available |
| QETB010 |
Wait until the save operation currently running has finished. |
| QETB011 |
System error occurred during the locking procedure |
| QETB012 |
No data available |
| QETB013 |
Position the cursor on a results field |
| QETB014 |
Cursor is incorrectly positioned (inspection point identification) |
| QETB015 |
& is not a valid date |
| QETB016 |
& is not a valid time |
| QETB017 |
Save first |
| QETB018 |
Wait until the save operation has finished |
| QETB019 |
No authorization |
| QETB020 |
Scrolling is not possible |
| QETB021 |
Save operation is running. Try function again later. |
| QETB022 |
You can only make STI evaluations for characs. with measured values |
| QETB023 |
Single values are required for STI evaluations |
| QETB024 |
You cannot record characteristic results for inspection lot & |
| QETB025 |
You cannot process this charac. with this transaction. |
| QETB026 |
There is no single result available |
| QETB027 |
There are no characteristics available with long-term inspections |
| QETB028 |
The field & must have an entry for the inspection point |
| QETB029 |
You must enter a partial lot for the inspection point |
| QETB030 |
You must enter a valuation for the inspection point |
| QETB031 |
You must enter a quantity for the inspection point |
| QETB032 |
You must enter a batch for the inspection point |
| QETB033 |
The characteristic is currently locked |
| QETB034 |
You cannot use this function in the entry line for new inspection points |
| QETB035 |
This Is Not a Long-Term Characteristic |
| QEWW100 |
Inspection lot is currently being processed by another user |
| QEWW101 |
Characteristics are currently being processed by another user |
| QEWW102 |
No inspection lots have been found with the selection conditions |
| QEWW103 |
No selection conditions exist for user &1 |
| QEWW104 |
Enter the number of nonconforming units |
| QEWW105 |
Enter the number of defects |
| QEWW106 |
You cannot enter a separator when recording results |
| QEWW107 |
Enter a valid measured value |
| QEWW108 |
You cannot save. Incorrect defect confirmations exist. |
| QEWW109 |
You cannot delete single values. Last status restored. |
| QEWW110 |
Data was recorded. Save or cancel results recording. |
| QEWW111 |
Too many single values were recorded. Delete single values. |
| QF000 |
*** Messages for defects recording |
| QF001 |
Insp.lot & already blocked by &- serial number maintenance not possible |
| QF002 |
Enter the number of items |
| QF003 |
Select entries first |
| QF004 |
Internal error during item number assignment |
| QF005 |
Report category & not available |
| QF006 |
Confirmation profile & does not exist |
| QF007 |
No quality notification type maintained for inspection lot type & |
| QF008 |
Defects can only be recorded at the lot level for the current insp.lot |
| QF009 |
Defects cannot be recorded for the characteristic |
| QF010 |
No item data is available for the header data |
| QF011 |
The cursor is not on a valid line |
| QF012 |
Internal error reading detail data |
| QF013 |
Default values were copied |
| QF014 |
Save not necessary |
| QF015 |
No catalog profile maintained for report type & |
| QF016 |
Defects for inspection lot & are blocked by & |
| QF017 |
System block could not be set- internal error |
| QF018 |
Operation & for inspection lot & is blocked by & |
| QF019 |
No report category could be determined automatically |
| QF020 |
Internal error determining the report category |
| QF021 |
Required entry not made |
| QF022 |
Defects already recorded for the selected object- only update possible |
| QF023 |
No defects have been recorded yet for the selected object |
| QF024 |
Error in internal table processing- table & |
| QF025 |
Clipboard is empty- internal error |
| QF026 |
The transfer parameters are inconsistent- internal error |
| QF027 |
Internal error with action & in table & |
| QF028 |
Function is not possible for completed item(s) |
| QF029 |
Updating selections |
| QF030 |
Text for operation not available |
| QF031 |
Status object & blocked by user & |
| QF032 |
Function is not possible for item(s) that have not yet been activated |
| QF033 |
Serial number profiles & not available |
| QF034 |
Serial number & cannot be used in inspection lot & |
| QF035 |
Serial number & for material & is already blocked by & |
| QF036 |
Serial numbers for inspection lot &, material & not available |
| QF037 |
No selection was made |
| QF038 |
No serial numbers have been created for inspection lot &, material & |
| QF039 |
Enter code group and code or use selection |
| QF040 |
New item has been inserted |
| QF041 |
You cannot delete closed items |
| QF042 |
Deleting entries |
| QF043 |
Function is not possible for item(s) that have already been activated |
| QF044 |
The notificiation types for the marked items are not identical |
| QF045 |
Creating serial numbers for inspection lot & is blocked |
| QF046 |
No further entries selected |
| QF047 |
Internal serial number management error |
| QF048 |
No quality notification type has been defined for inspection type & |
| QF049 |
Defect data for inspection lot & is being saved |
| QF050 |
This line cannot be selected |
| QF051 |
List contains defect records that are not yet saved |
| QF052 |
Automatic assignment of report category to work center is not possible |
| QF053 |
Masked plant '*' only permissible for masked work center '*' |
| QF054 |
Masking with '*' only possible as last character |
| QF055 |
Plant & cannot be found |
| QF056 |
Work center & is not available |
| QF057 |
No notifications have been created for the selected defect records |
| QF058 |
Only notifications for posted defect records can be displayed |