| QP466 |
Target value is less than the lower specification limit 1 |
| QP467 |
Target value is greater than the upper specification limit 1 |
| QP468 |
Target value is less than the lower specification limit 2 |
| QP469 |
Target value is greater than upper specification limit 2 |
| QP470 |
Target value is greater than the upper plausibility limit |
| QP471 |
Target value is less than the lower plausibility limit |
| QP472 |
Target value is greater than the upper specification limit |
| QP473 |
Target value is less than the lower specification limit |
| QP474 |
Entering a dynamic modification rule is not allowed |
| QP475 |
No formula is defined for the inspection characteristic |
| QP476 |
No test equipment assigned |
| QP477 |
Item number &1 for the test equipment of operation &2 is not clear |
| QP480 |
The current valid version of &1 is not released |
| QP481 |
You can only use vendor or cust. selection criteria with ref. to a mat. |
| QP482 |
No characteristics could be determined with your specifications |
| QP483 |
Identifier incomplete: You must uniquely specify object-dep. char. spec. |
| QP490 |
Tolerance change: from-date is greater than the to-date |
| QP491 |
Time period of the tolerance change is not within the validity range |
| QP493 |
Tolerance change exceeds the upper plausibility limit |
| QP494 |
Tolerance change falls below the lower plausibility limit |
| QP497 |
Enter a time period for the tolerance change |
| QP498 |
Only status & is allowed |
| QP500 |
Unit & cannot be converted into the operation unit & |
| QP501 |
Sample unit &1 is not compatible with task list unit of measure & |
| QP502 |
Mark inspection characteristics for deletion |
| QP503 |
Mark dependent characteristic specifications for deletion |
| QP504 |
Non-relevant fields will be initialized |
| QP505 |
Unit & cannot be converted in header unit of measure & |
| QP506 |
Internal errors are initialized by the system (&1) |
| QP507 |
Consistency check: Field is initialized (&1 &2) |
| QP516 |
The entry is not reccognized as a selected set |
| QP520 |
You have not assigned the insp. point description in the task list header |
| QP522 |
Dynamic modification level was initialized for task list usage &1 |
| QP523 |
Dynamic modification rule was initialized for task list usage & |
| QP524 |
Replace sampling procedure for inspection characteristics if required |
| QP538 |
Check characteristic number & |
| QP539 |
Check assignment number & |
| QP540 |
Enter characteristic number |
| QP541 |
Enter increment |
| QP550 |
Discrepancy between memory and memory management of operation data |
| QP560 |
Enter the plant for the master inspection characteristic & |
| QP565 |
Check the target value. A tolerance key is used |
| QP566 |
No relative specification limits defined for target value |
| QP570 |
Check the interval reference |
| QP571 |
Check the selected set |
| QP572 |
No code was selected |
| QP573 |
All selected sets are used for the selection |
| QP574 |
The tolerance key is being reset |
| QP575 |
No authorization to change characteristics. You can only display them |
| QP576 |
Error during authorization check. Contact your system administrator |
| QP577 |
You are not authorized to include characteristic &1 &2 &3 |
| QP578 |
Ch &1: You are not authorized to include insp. method &2 &3 &4 |
| QP579 |
Charac. &1: Deselecting "Calculate formula" indicator |
| QP580 |
Charac. &1: Link exists to dynamic modification for characteristic &2 |
| QP581 |
Charac. &1: Cancelling test equipment assignment |
| QP582 |
Characteristic &1 is a conditional characteristic |
| QP585 |
CH &2: There is more than one selected set for catalog &1 |
| QP600 |
Last selected operation reached |
| QP601 |
Check the selections for the operation |
| QP602 |
First selected operation reached |
| QP615 |
Tolerance & is not defined |
| QP616 |
Fields that are dependent on the tolerance key will not be copied |
| QP617 |
Copying characteristic data from the tolerance key |
| QP620 |
Define the control key profile & |
| QP621 |
Control indicator and tolerance key are not compatible |
| QP622 |
Limit values and class definitions were reset |
| QP623 |
Target value is set to zero (relative tolerances) |
| QP624 |
Lower relative specification limit is not negative |
| QP625 |
Tolerance change results in an incorrect tolerance range |
| QP626 |
Tolerance change not compatible with the target value |
| QP627 |
Upper relative specification limit not positive |
| QP630 |
Conflict for at least 1 characteristic due to change number |
| QP631 |
Conflict for at least 1 dep. char. spec. due to change number |
| QP638 |
Expand class width |
| QP645 |
Upper limit for the copy interval is overwritten with & |
| QP648 |
You have not entered a distribution type for a quantitative character. |
| QP650 |
You cannot delete a characteristic that is referenced in plans |
| QP651 |
You cannot delete dependent characteristic specs referenced in plans |
| QP659 |
Data for dependent characteristic specifications (&1) are not consistent |
| QP660 |
The inspection characteristic data &1 is inconsistent |
| QP661 |
The key for the master insp. characteristic & was not completely entered |
| QP662 |
You do not have authorization (&) to assign master data |
| QP663 |
The key for inspection method & was not completely entered |
| QP664 |
Master insp. characteristic & & & cannot be referenced (inconsistent) |
| QP670 |
Enter an upper specification limit |
| QP671 |
Enter a lower specification limit |
| QP672 |
Enter a class number, class width and class midpoint |
| QP673 |
Enter a formula for calculating characteristic results |
| QP674 |
Enter a target value |
| QP675 |
Error when reading a change indicator |
| QP676 |
Error when writing the change indicator status |
| QP677 |
Enter a key for input processing |
| QP700 |
No assignment available for the plan |
| QP701 |
Dependent characteristic specifications are also deleted |
| QP702 |
The changes are copied to dependent characteristic specifications |
| QP711 |
An internal error occurred when you called up the function |
| QP712 |
No entry was found using the classification system |
| QP713 |
No entry was selected |
| QP750 |
Error during transfer to report RQPAAS00 |
| QP800 |
No task list characteristics were selected |